smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-26-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: 64FFP7YDT
LU WWN Device Id: 5 000039 5928857d5
Firmware Version: AX0R2J
User Capacity: 1.000.204.886.016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun May 3 13:49:24 2020 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 239) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1441
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 3400
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 072 072 000 Old_age Always - 11440
10 Spin_Retry_Count 0x0033 167 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3354
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 4496
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 250
193 Load_Cycle_Count 0x0032 095 095 000 Old_age Always - 57116
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 33 (Min/Max 24/49)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 3528
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 075 075 000 Old_age Always - 10362
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 260
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 43762 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 43762 occurred at disk power-on lifetime: 11440 hours (476 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 48 00 00 00 40 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 48 00 00 00 40 00 00:10:01.308 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:10:01.307 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:10:01.307 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:10:01.306 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 00:10:01.306 SET FEATURES [Set transfer mode]
Error 43761 occurred at disk power-on lifetime: 11440 hours (476 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 30 00 00 00 40 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 30 00 00 00 40 00 00:09:57.467 READ FPDMA QUEUED
60 08 28 a0 6d 70 40 00 00:09:57.466 READ FPDMA QUEUED
60 08 20 00 6d 70 40 00 00:09:57.434 READ FPDMA QUEUED
ec 00 01 00 00 00 00 00 00:09:57.432 IDENTIFY DEVICE
ec 00 01 00 00 00 00 00 00:09:57.429 IDENTIFY DEVICE
Error 43760 occurred at disk power-on lifetime: 11440 hours (476 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 30 00 00 00 40 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 30 00 00 00 40 00 00:09:53.601 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:09:53.600 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:09:53.599 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:09:53.599 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 00:09:53.598 SET FEATURES [Set transfer mode]
Error 43759 occurred at disk power-on lifetime: 11440 hours (476 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 90 00 00 00 40 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 20 a0 6d 70 40 00 00:09:49.755 READ FPDMA QUEUED
60 08 90 00 00 00 40 00 00:09:49.728 READ FPDMA QUEUED
60 08 80 00 6d 70 40 00 00:09:49.728 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:09:49.728 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:09:49.727 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 43758 occurred at disk power-on lifetime: 11440 hours (476 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 f8 00 00 00 40 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 18 00 6d 70 40 00 00:09:45.899 READ FPDMA QUEUED
60 08 f8 00 00 00 40 00 00:09:45.899 READ FPDMA QUEUED
ec 00 01 00 00 00 00 00 00:09:45.896 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 00 00:09:45.896 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:09:45.896 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
