Ativar Wake On Lan no host

Good_speed
(usa Debian)

Enviado em 02/01/2019 - 15:39h

Amigos, boa tarde

Estou precisando ativar o WOL no meu host Proxmox 5.2, já pesquisei no google mais não obtive sucesso relacionado ao proxmox, só achei relacionado ao debian 9 e mesmo assim não funcionou, o WOL foi ativado na BIOS do computador, alguém poderia ajudar?

Interface física
enp3s0f0:
enp3s0f1:
enp4s0f0:
enp4s0f1:
enp0s25:

Virtual
vmbr0:
vmbr1:

Interface com WOL
enp3s0f0
enp3s0f1
enp0s25

# uname -a
Linux pveceph02 4.15.17-1-pve #1 SMP PVE 4.15.17-9 (Wed, 9 May 2018 13:31:43 +0200) x86_64 GNU/Linux


# lspci

00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 05)
03:00.0 Ethernet controller: Broadcom Limited NetXtreme II BCM5709 Gigabit Ethernet (rev 20)
03:00.1 Ethernet controller: Broadcom Limited NetXtreme II BCM5709 Gigabit Ethernet (rev 20)
04:00.0 Ethernet controller: Broadcom Limited NetXtreme II BCM5709 Gigabit Ethernet (rev 20)
04:00.1 Ethernet controller: Broadcom Limited NetXtreme II BCM5709 Gigabit Ethernet (rev 20)

# ethtool enp3s0f0
Settings for enp3s0f0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: Unknown!
Duplex: Half
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: off
Supports Wake-on: g
Wake-on: g
Link detected: no

# ethtool enp3s0f1
Settings for enp3s0f1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: Unknown!
Duplex: Half
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: off
Supports Wake-on: g
Wake-on: g
Link detected: no

# ethtool enp4s0f0
Settings for enp4s0f0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: Unknown!
Duplex: Half
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: off
Supports Wake-on: d
Wake-on: d
Link detected: no

# ethtool enp4s0f1
Settings for enp4s0f1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: on
Supports Wake-on: d
Wake-on: d
Link detected: yes

# ethtool enp0s25
Settings for enp0s25:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: on (auto)
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes

# ethtool vmbr0
Settings for vmbr0:
Link detected: yes

# ethtool vmbr1
Settings for vmbr1:
Link detected: yes

Obrigado pela ajuda...