TL-WDN3200

beyraq
(usa Arch Linux)

Enviado em 01/02/2016 - 17:01h

alguem me ajuda configurar e como conectar no Linux Mint?

dmesg, nao configurei nada antes, so pluguei

[ 5711.486248] usb 8-4: USB disconnect, device number 3
[ 5713.731192] usb 3-1: new low-speed USB device number 3 using xhci_hcd
[ 5713.881931] usb 3-1: New USB device found, idVendor=045e, idProduct=00cb
[ 5713.881941] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5713.881946] usb 3-1: Product: Microsoft USB Optical Mouse
[ 5713.881951] usb 3-1: Manufacturer: PixArt
[ 5713.882362] usb 3-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 5713.896415] input: PixArt Microsoft USB Optical Mouse as /devices/pci0000:00/0000:00:10.1/usb3/3-1/3-1:1.0/0003:045E:00CB.0005/input/input19
[ 5713.947258] hid-generic 0003:045E:00CB.0005: input,hidraw2: USB HID v1.11 Mouse [PixArt Microsoft USB Optical Mouse] on usb-0000:00:10.1-1/input0
[ 5718.537987] usb 6-5: new high-speed USB device number 4 using ehci-pci
[ 5718.670633] usb 6-5: New USB device found, idVendor=148f, idProduct=5572
[ 5718.670640] usb 6-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5718.670645] usb 6-5: Product: 802.11 n WLAN
[ 5718.670648] usb 6-5: Manufacturer: Ralink
[ 5718.670651] usb 6-5: SerialNumber: 1.0
[ 5718.900427] cfg80211: World regulatory domain updated:
[ 5718.900434] cfg80211: DFS Master region: unset
[ 5718.900436] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 5718.900441] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 5718.900445] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 5718.900449] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 5718.900452] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 5718.900455] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 5719.037552] usb 6-5: reset high-speed USB device number 4 using ehci-pci
[ 5719.163333] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5592, rev 0222 detected
[ 5719.191926] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 000f detected
[ 5719.200824] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 5719.201558] usbcore: registered new interface driver rt2800usb
[ 5719.243044] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 5719.243523] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[ 5719.511772] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

clodoaldops
(usa Linux Mint)

Enviado em 04/02/2016 - 09:36h

1- qual linux vc está usando: nome e versão ?

2- se vc não está conseguindo se conectar usando uma wifi-usb , diga nome/modelo/marca do adaptador??

3-aqui tenho um wifi-usb intelbras-WBN 300 com chipset Ralink-RT5372 que funciona automaticamente com ubuntu-14.04 e linuxmint-17 automaticamente

clodoaldops
(usa Linux Mint)

Enviado em 04/02/2016 - 09:46h

Sim, ninguem sabe como um clicador que quase não usa terminal , que não é hard user consegue isso!
kkkkkkk

removido
(usa Nenhuma)

Enviado em 04/02/2016 - 09:58h

A mensagem fala sobre aguardando um endereço IPV6!

[ 5719.511772] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

Desative o IPV6 no boot.

ipv6.disable=1

e teste.