Análise de dmesg

renato_pacheco
(usa Debian)

Enviado em 08/02/2008 - 00:22h

Alguém poderia analisar o meu dmesg? O meu Slack 12 tá funcionando, mas cheio d erros. Um detalhe: muito dos módulos carregados não estão como built-in no kernel e não constam no rc.modules e nem no modprobe.conf!

Linux version 2.6.21.5-smp (root@midas) (gcc version 4.1.2) #2 SMP Tue Jun 19 14:58:11 CDT 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000003fef0000 end: 000000003fff0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000003fff0000 size: 0000000000003000 end: 000000003fff3000 type: 4
copy_e820_map() start: 000000003fff3000 size: 000000000000d000 end: 0000000040000000 type: 3
copy_e820_map() start: 00000000d0000000 size: 0000000010000000 end: 00000000e0000000 type: 2
copy_e820_map() start: 00000000fec00000 size: 0000000001400000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000d0000000 - 00000000e0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f4d60
Entering add_active_range(0, 0, 262128) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262128
early_node_map[1] active PFN ranges
0: 0 -> 262128
On node 0 totalpages: 262128
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 255 pages used for memmap
HighMem zone: 32497 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP 000F6700, 0014 (r0 GBT )
ACPI: RSDT 3FFF3040, 0030 (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
ACPI: FACP 3FFF30C0, 0074 (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
ACPI: DSDT 3FFF3180, 38E4 (r1 GBT AWRDACPI 1000 MSFT 100000C)
ACPI: FACS 3FFF0000, 0040
ACPI: MCFG 3FFF6B80, 003C (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
ACPI: APIC 3FFF6AC0, 0068 (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:90000000)
Built 1 zonelists. Total pages: 260081
Kernel command line: auto BOOT_IMAGE=Linux ro root=806
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2660.293 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1029484k/1048512k available (6215k kernel code, 18360k reserved, 2017k data, 392k init, 131008k highmem)
virtual kernel memory layout:
fixmap : 0xffe17000 - 0xfffff000 (1952 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0915000 - 0xc0977000 ( 392 kB)
.data : 0xc0711c79 - 0xc090a38c (2017 kB)
.text : 0xc0100000 - 0xc0711c79 (6215 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5325.62 BogoMIPS (lpj=10651249)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000651d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003180 0000651d 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 24k freed
ACPI: Core revision 20070126
CPU0: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 01
Total of 1 processors activated (5325.62 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
libata version 2.20 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:0b: ioport range 0x400-0x4bf could not be reserved
pnp: 00:0c: iomem range 0xd0000000-0xdfffffff could not be reserved
pnp: 00:0d: iomem range 0xd0000-0xd7fff has been reserved
pnp: 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
pnp: 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:0d: iomem range 0xfc000-0xfffff could not be reserved
ieee1394: Initialized config rom entry `ip1394'
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:1e.0
IO window: a000-afff
MEM window: f0000000-f2ffffff
PREFETCH window: e0000000-efffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.28 [Flags: R/W].
JFS: nTxBlock = 8045, nTxLock = 64362
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.3.3
OCFS2 Node Manager 1.3.3
OCFS2 DLM 1.3.3
OCFS2 DLMFS 1.3.3
OCFS2 User DLM kernel interface loaded
GFS2 (built Jun 19 2007 14:57:33) installed
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Switched to high resolution mode on CPU 0
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.14)
input: Macintosh mouse button emulation as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
ICH6: chipset revision 5
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: GCR-8523B, ATAPI CD/DVD-ROM drive
hdb: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 52X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
Loading iSCSI transport class v2.0-724.
iscsi: registered transport (tcp)
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver (1.1-5[2423]-mh3)
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.1.11
Copyright(c) 2004-2006 Emulex. All rights reserved.
seagate: ST0x/TMC-8xx not detected.
Failed initialization of WD-7000 SCSI card!
DC390: clustering now enabled by default. If you get problems load
with "disable_clustering=1" and report to maintainers
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.10-rc1 Wed Feb 14 10:14:25 PST 2007
GDT-HA: Storage RAID Controller Driver. Version: 3.05
GDT-HA: Found 0 PCI Storage RAID Controllers
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.008.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.3.1 (January 23, 2007)
RocketRAID 3xxx SATA Controller driver v1.0 (060426)
st: Version 20070203, fixed bufsize 32768, s/g segs 256
ata_piix 0000:00:1f.2: version 2.10ac1
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x0001d000 ctl 0x0001d402 bmdma 0x0001e000 irq 17
ata2: SATA max UDMA/133 cmd 0x0001d800 ctl 0x0001dc02 bmdma 0x0001e008 irq 17
scsi2 : ata_piix
ata1.00: ATA-7: SAMSUNG HD120IJ, ZL100-33, max UDMA7
ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi3 : ata_piix
ATA: abnormal status 0x7F on port 0x0001d807
scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD120IJ ZL10 PQ: 0 ANSI: 5
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 >
sd 2:0:0:0: Attached scsi disk sda
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.04
Fusion MPT FC Host driver 3.04.04
Fusion MPT SAS Host driver 3.04.04
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 18, io mem 0xf3000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 18, io base 0x0000bc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000b000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000b400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000b800
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usb 4-2: new full speed USB device using uhci_hcd and address 2
usb 4-2: unable to read config index 0 descriptor/start
usb 4-2: chopping to 0 config(s)
usb 4-2: no configuration chosen from 0 choices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1 666 MB/s
raid6: int32x2 749 MB/s
raid6: int32x4 601 MB/s
raid6: int32x8 506 MB/s
raid6: mmxx1 1620 MB/s
raid6: mmxx2 1902 MB/s
raid6: sse1x1 952 MB/s
raid6: sse1x2 1870 MB/s
raid6: sse2x1 1923 MB/s
raid6: sse2x2 2922 MB/s
raid6: using algorithm sse2x2 (2922 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 4288.000 MB/sec
raid5: using function: pIII_sse (4288.000 MB/sec)
md: multipath personality registered for level -4
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
input: AT Translated Set 2 keyboard as /class/input/input1
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 392k freed
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 915G Chipset.
agpgart: AGP aperture is 256M @ 0x0
kobject_add failed for uhci_hcd with -EEXIST, don't try to register things with the same name in the same directory.
[<c03e86f7>] kobject_shadow_add+0x117/0x1a0
[<c013fba4>] mod_sysfs_setup+0x24/0xb0
[<c0141458>] sys_init_module+0x1648/0x1940
[<c0102ae8>] syscall_call+0x7/0xb
[<c0710000>] __mutex_lock_slowpath+0x40/0x90
=======================
intel_rng: FWH not detected
kobject_add failed for uhci_hcd with -EEXIST, don't try to register things with the same name in the same directory.
[<c03e86f7>] kobject_shadow_add+0x117/0x1a0
[<c013fba4>] mod_sysfs_setup+0x24/0xb0
[<c0141458>] sys_init_module+0x1648/0x1940
[<c0102ae8>] syscall_call+0x7/0xb
[<c0710000>] __mutex_lock_slowpath+0x40/0x90
=======================
kobject_add failed for uhci_hcd with -EEXIST, don't try to register things with the same name in the same directory.
[<c03e86f7>] kobject_shadow_add+0x117/0x1a0
[<c013fba4>] mod_sysfs_setup+0x24/0xb0
[<c0141458>] sys_init_module+0x1648/0x1940
[<c0102ae8>] syscall_call+0x7/0xb
[<c0710000>] __mutex_lock_slowpath+0x40/0x90
=======================
kobject_add failed for uhci_hcd with -EEXIST, don't try to register things with the same name in the same directory.
[<c03e86f7>] kobject_shadow_add+0x117/0x1a0
[<c013fba4>] mod_sysfs_setup+0x24/0xb0
[<c0141458>] sys_init_module+0x1648/0x1940
[<c0102ae8>] syscall_call+0x7/0xb
[<c0710000>] __mutex_lock_slowpath+0x40/0x90
=======================
iTCO_vendor_support: vendor-support=0
i2c_core: exports duplicate symbol i2c_smbus_write_i2c_block_data (owned by kernel)
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 17
kobject_add failed for ehci_hcd with -EEXIST, don't try to register things with the same name in the same directory.
[<c03e86f7>] kobject_shadow_add+0x117/0x1a0
[<c013fba4>] mod_sysfs_setup+0x24/0xb0
[<c0141458>] sys_init_module+0x1648/0x1940
[<c0102ae8>] syscall_call+0x7/0xb
=======================
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH6 or ICH6R TCO device (Version=2, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
sd 2:0:0:0: Attached scsi generic sg0 type 0
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1e.2 to 64
i2c_core: exports duplicate symbol i2c_smbus_write_i2c_block_data (owned by kernel)
Linux video capture interface: v2.00
i2c_core: exports duplicate symbol i2c_smbus_write_i2c_block_data (owned by kernel)
i2c_core: exports duplicate symbol i2c_smbus_write_i2c_block_data (owned by kernel)
i2c_algo_bit: exports duplicate symbol i2c_bit_add_bus (owned by kernel)
i2c_algo_bit: exports duplicate symbol i2c_bit_add_bus (owned by kernel)
intel8x0_measure_ac97_clock: measured 54731 usecs
intel8x0: clocking to 48000
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 21 (level, low) -> IRQ 21
eth0: RealTek RTL8139 at 0xa000, 00:0f:ea:ae:2b:93, IRQ 21
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 20 (level, low) -> IRQ 22
bttv0: Bt878 (rev 17) at 0000:01:01.0, irq: 22, latency: 32, mmio: 0xe8080000
bttv0: using: Prolink Pixelview PV-BT878P+ (Rev.4C,8E) [card=70,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00ffc0ff [init]
bttv0: using tuner=25
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
i2c_core: exports duplicate symbol i2c_smbus_write_i2c_block_data (owned by kernel)
bttv0: i2c: checking for TDA9887 @ 0x86... not found
i2c_core: exports duplicate symbol i2c_smbus_write_i2c_block_data (owned by kernel)
tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw])
tuner 1-0061: type set to 25 (LG PAL_I+FM (TAPC-I001D))
tuner 1-0061: type set to 25 (LG PAL_I+FM (TAPC-I001D))
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
input: bttv IR (card=70) as /class/input/input2
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.05 Tue Jan 22 19:36:58 PST 2008
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:01:01.1[A] -> GSI 20 (level, low) -> IRQ 22
bt878_probe: card id=[0x0],[ <NULL> ] has DVB functions.
bt878(0): Bt878 (rev 17) at 01:01.1, irq: 22, latency: 32, memory: 0xe8081000
Adding 497972k swap on /dev/sda7. Priority:-1 extents:1 across:497972k
EXT3 FS on sda6, internal journal
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
i2c_core: exports duplicate symbol i2c_smbus_write_i2c_block_data (owned by kernel)
i2c_core: exports duplicate symbol i2c_smbus_write_i2c_block_data (owned by kernel)
i2c_algo_bit: exports duplicate symbol i2c_bit_add_bus (owned by kernel)
usbcore: registered new interface driver gspca
/home/renato/downloads/gspcav1-20071224/gspca_core.c: gspca driver 01.00.20 registered
Capability LSM initialized
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
input: ImPS/2 Generic Wheel Mouse as /class/input/input3
fuse init (API version 7.8)
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
NVRM: not using NVAGP, an AGPGART backend is loaded!

Obrigado!

cytron
(usa Slackware)

Enviado em 16/02/2008 - 20:37h

Esquenta com isso não, tudo isso é normal, nem chega a ser considerado erro.

Se você ver o que acontece no background do KDE é capaz de nem dormir... ou você sairá correndo sem camisa por toda a cidade. kkkkkk!!!